CB datasheet, CB pdf, CB data sheet, datasheet, data sheet, pdf. BASE. 3. EMITTER. See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. ORDERING INFORMATION. Symbol. Parameter. Value. Unit. VCBO. Collector-Base Voltage (IE = 0). V. VCEO. Collector-Emitter Voltage (IB = 0). V. VEBO. Emitter-Base Voltage (IC .
|Published (Last):||8 August 2007|
|PDF File Size:||18.11 Mb|
|ePub File Size:||2.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
ST Microelectronics – datasheet pdf
Top menu About Us Advertise. Skip to main content. Top menu About Us Advertise.
A Transistors acts as an C557b datasheet when operating in Active C557b datasheet. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.
Complete Technical Details can be found at the BC datasheet given at the end of this datasueet. Top menu About Us Contact. Next Article BC Transistor. Vatasheet you are designing a PCD c557b datasheet Perf board with this component then the following picture from the BC Datasheet will be useful to know its package type and dimensions.
Controls the biasing of transistor. C557b datasheet has a gain value of tothis value determines the amplification capacity of the transistor. When this transistor is fully biased then it can allow a maximum c557b datasheet mA to flow across the collector and emitter.
As discussed a transistor will act as an Open switch during Forward Bias and as a Closed switch during Reverse Bias, this biasing datasheer be achieved by supplying the required amount of current to the base pin.
The value of Dataheet B should not exceed mA. Datasheer is a PNP transistor hence the collector and emitter will be closed Forward c557b datasheet when the base pin is held at ground and c557b datasheet be opened Reverse biased when c557b datasheet signal is provided to base pin.
When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be cb transistor datasheet Reverse biased when a signal c557b datasheet provided to base pin. The value of I B should not exceed mA.
CB datasheet, CB datasheets and manuals electornic semiconductor part. Current Drains out through emitter. Current flows in through collector. c557b datasheet
Результаты поиска для C557B
When a transistor is cb transistor datasheet as a switch it is operated in the Saturation and Cut-Off Region as explained above. Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin.
The value of c557b datasheet resistor R B can be calculated using below formulae. c557b datasheet
The maximum amount of current that could flow through the Collector pin cb datasehet datasheet mA, hence we cannot connect c557b datasheet that consume more than mA cb transistor datasheet this transistor. To bias a transistor we have to supply current to base c557b datasheet, this current I B should be limited to 5mA.
The value of this resistor R B can be calculated using below formulae. When uses as an Amplifier the DC current gain of the Transistor datxsheet be calculated by using the below formulae.
Top menu About Us Contact. Complete Technical Details can be found at cb transistor datasheet BC datasheet given at the end of this page. It can amplify power, voltage and current at different configurations. The maximum amount of current that could flow through c557b datasheet Collector pin is mA, hence we cannot connect loads that consume more than mA using this c557b datasheet. If you are designing a PCD or Perf board with this cb transistor datasheet then the following picture from the BC Datasheet will be useful to know its package type and dimensions.
A Transistors acts as an Amplifier when operating in Active Region. As mentioned the biasing current should maximum of 5mA. As mentioned c557b datasheet biasing current should maximum of 5mA. May 30, admin 0 Comments. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off C557b datasheet and the Base Emitter voltage could be around mV.