ENDA ETC 9420 PDF

NOTE: ETC ENDA ETC series are intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding. Thank you for choosing ENDA EPC profile controller. * Selectable SSR or While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive. Double set point. Selectable sensor type (Pt, J, K, L, T, S, R). PID control function with accurate self-tuning. Digital inputs can be assigned to 3 different.

Author: Kazrakasa Kazidal
Country: Bahrain
Language: English (Spanish)
Genre: Automotive
Published (Last): 15 September 2018
Pages: 280
PDF File Size: 2.54 Mb
ePub File Size: 18.46 Mb
ISBN: 582-5-38907-566-8
Downloads: 91408
Price: Free* [*Free Regsitration Required]
Uploader: Fauzilkree

When self tune procedure begins with no failure, Pid. S different from out1.

During an installation, all of the cables that are connected to the device must ebda free of energy. Before self tune procedure, temperature setpoint value should be adjusted. If the selected input type is changed, the value of C. Set appears on the display.

Adjustable between 1 and seconds. RS Modbus communication None IP65 Rated population degree Rear panel: While holding 25 REdY. These cables should not be close to the power cables or components. If independent or deviation alarm is selected, this parameter can be Lo.

Technical Specification

UnIt Offset value is added to the measurement value. All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. CSET If key is pressed and held 0. Four kinds of ennda can be selected. If deviation alarm is selected, A1. Set point during normal operation Date value during programming SET Do not use the device in locations subject to corrosive and flammable gases. Adjustable between 0 and minutes. Relative humidity According to EN Front panel: If process value is Appropriate to begin self tune, rEdY.

TOP Related  MECANICA VECTORIAL PARA INGENIEROS ESTATICA HIBBELER PDF

If band edna is selected, A1. Then the device heats until setpoint value according to PID parameters and calculates the energyrequirement for stable If the parameter is 31, the filter run most slow.

Using this parameter the energy requirements of the system is adjusted at the set point. Before self tune procedure, A. Selectable logic control output. If 0 is selected, soft start feature will be enable and the device reaches set point value quickly. When PID parameters are Filter for display value. After PID is calculated A.

Alternatively, the same function occurs first pressing Entering from the programming mode to the run mode: Then, the value is adjusted by using If C.

Technical Specification |

The maximum value is the value of A1. Pay attention to the polarities of the thermocouple cables as shown in the figure right are connected to the. While cleaning the device, solvents thinner, benzine, acid etc.

TOP Related  AWAZ E DOST MUKHTAR MASOOD DOWNLOAD

The device must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. SEt is the value of C.

The normal value is 0. Therefore, when using a grounding thermocouple, do not connect the logic output terminals to the ground.

Then press any key to see Pid. It’s a community-based project which helps to repair anything. Enter PID parameters of the system if they are known at the begining. Difference addresses should be selected for every device.

Otherwise, Self-Tune should be activated. Use suitable compensation cables. The same procedure is valid for the decrement key. The maximum value is the value of C. The value of parameter should be increased in interference.

IfInp parameter is selected TC or Pt, this parameter is seen. If waited enough,the value increases at each step.

Enda ETC Series PID Temperature Controllers Panel Mount | Rapid Online

Then, the value is adjusted by using PV A1. If any key is pressed while P. Process value during normal operation Mnemonic parameter code during programming SV Display: